Controller Supply-HM-V1-T

Controller Supply-HM-V1-T

RF remote, 0/1-10V, Push Dim (3-in-1) memalapkan.
4096 tahap 0-100% dimming smoothly without any flflash.
Match with RF 2.4G single zone or multiple zone dimming remote control.

Satu pengawal RF menerima sehingga 10 kawalan jauh.
Fungsi auto-penghantaran: Controller automatically transmit signal to another controller with 15m control distance.

Segerakkan pada pelbagai pengawal.
Connect with external push switch to achieve on/off and 0-100% fungsi dimming.

Cahaya hidup/mati pudar 3s dipilih.
Lebih panas / Lebih banyak / Perlindungan litar pintas, pulih secara automatik

Hantarkan E-mel kepada Kami Hubungi sekarang Muat turun sebagai PDF

Perincian Produk Maklum balas sekarang

Inpuf and Oufput
Input voliage	12-24VDC
Input current	20.5A
Output voltage	12-24VDC
Output current	1CH,20A
Output power	240W/480W (12V/24V)
Ouput ype	Constant volage

Dimming data
Input signal	RF 2.4GHz 0/1-10V Push Dim
Control distance	15m(Barrier-free space)
Dimming gray scale	4096(2^12)tahap
Dimming range	0 -100%
Dimming curve	Logarithmic
PWM Frequency	500Hz(default)

Safety and EMC
EMC standard (EMC)	ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD	EN 62368-1:2020+A11:2020
Radio Equipment(RED)	ETSI EN 300 328 V2.2.2
Pensijilan	CE,EMC,LVD,RED

Environment
Operation temperature	Ta: -30°C ~ +55°C
Case temperature (Max.)	T c:+85° C.
Peringkat IP	IP20

Warranty and Protection

Jaminan

5 tahun

Protection

Reverse polarity

Lebih panas

Lebih banyak

Litar pintas

Weight
Net weight	0.234kg
Gross weight	0.054kg

Mechanical Structures and Installations

Wiring Diagram

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

0/1-10V Dimming

The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.

Compliant with 0-10V, 1-10V, 10V PWM, RX(4 dalam 1).
We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 meters.

If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

Short press:

Turn on or off light.

Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 meters.

Dimming Curve

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Malfunctions Analysis & Troubleshooting

Malfunctions	Causes	Troubleshooting
No light	1. No power. 2.Wrong connection or insecure.	1.Check the power. 2.Check the connection.
Uneven intensity between front and rear,with voltage drop	1. Output cable is too long. 2. Wire diameter is too small. 3.Overload beyond power supply capability. 4.Overload beyond controller capability.	1.Reduce cable or loop supply. 2.Change wider wire. 3.Replace higher power supply. 4.Add power repeater.
No response from the remote	1.The battery has no power. 2. Beyond controllable distance. 3.The controller did not match the remote.	1. Replace battery. 2.Reduce remote distance. 3. Re-match the remote.

Controller Supply-HM-V1-T-

Q1.ls baik untuk OEM dan ODM ?

Lampu perisai adalah profesional untuk pesanan OEM dan ODM. Kami mempunyai pengalaman yang kaya dengan pengeluaran dan memastikan kualiti yang baik.

Q2.What's the Moq? Bolehkah saya mempunyai beberapa contoh ?

MOQ rendah, 1 PC untuk kualiti pemeriksaan sampel tersedia Sampel Sampel adalah penerimaan dan selamat datang sampel yang disesuaikan untuk projek anda.

Q3. Berapa lama masa utama?

Keperluan sampel 3-5 hari-hari, pesanan kuantiti memerlukan 10-15days

Q4. Bagaimana anda menghantar barang dan berapa lama masa yang diperlukan untuk tiba?

Kami biasanya menghantar melalui DHL, UPS, FedEx atau TNT. Ia biasanya mengambil 3-5 hari untuk tiba. Penghantaran laut juga pilihan.

Q5. Bagaimana untuk meneruskan pesanan untuk cahaya yang disesuaikan ?

Pertama, beritahu kami keperluan atau lukisan anda. Kedua, kami memetik mengikut anda., anda mengesahkan dan mengatur pembayaran untuk pesanan rasmi. Akhirnya, Kami akan memulakan pengeluaran dan mengatur penghantaran.

Q6. Berapa lama jaminan?

Semua kualiti produk lampu Armor adalah 3 tahun, Produk projek yang disesuaikan dengan jaminan 5 tahun.

Q7.ls baik untuk mencetak logo saya pada produk ?

Ya, Sila maklumkan kami secara rasmi sebelum pengeluaran dan sahkan reka bentuk yang pertama berdasarkan sampel kami.

Q8. bagaimana untuk menangani yang salah?

Kami menawarkan 2, 3 dan 5 Jaminan terhad tahun untuk pelbagai jenis produk atau projek pencahayaan yang berbeza. Dalam tempoh ini, Sekiranya pelanggan mempunyai masalah kualiti bukti dan bukti itu diluluskan oleh jurutera pencahayaan perisai, Kami ingin menggantikan yang cacat dengan barang -barang yang berkelayakan baru.

Sila ambil perhatian bahawa jaminan tidak sama dengan jangka hayat. Produk kami mempunyai lebih daripada 50000 jam jangka hayat.

Q9.Can L Lawati Kilang Anda?

Pasti,selamat datang untuk melawat kilang kami. Dapat memberitahu kami jadual lawatan anda sebelum dua hari dan produk yang berminat.

Q10. Adakah anda kilang atau syarikat perdagangan?

Kami adalah kilang eksport langsung ke pasar laut.

Q11. Adakah anda membekalkan lampu led ke mana-mana kedai jenama Lighting yang terkenal?

Ya,Kedai utama kami Lighting mempunyai bekalan ke LANCOME , LEGO,SETERUSNYA,JURULATIH, Lebah Burt,Hasbro, Kasut，KELAPA,M&S dll.