Controller Supply-HM-V1-T

Controller Supply-HM-V1-T

RF remote, 0/1-10V, Push Dim (3-in-1) dimma.
4096 levels 0-100% dimming smoothly without any flflash.
Match with RF 2.4G single zone or multiple zone dimming remote control.

One RF controller accept up to 10 remote control.
Auto-transmitting function: Controller automatically transmit signal to another controller with 15m control distance.

Synchronize on multiple number of controllers.
Connect with external push switch to achieve on/off and 0-100% dimming function.

Light on/off fade time 3s selectable.
Over-heat / Over-load / Short circuit protection, recover automatically

Sendu tölvupóst til okkar Hafðu samband núna Sækja sem PDF

Upplýsingar um vöru Endurgjöf núna

Inpuf and Oufput
Input voliage	12-24VDC
Input current	20.5A
Output voltage	12-24VDC
Output current	1CH,20A
Output power	240W/480W (12V/24V)
Ouput ype	Constant volage

Dimming data
Input signal	RF 2.4GHz 0/1-10V Push Dim
Control distance	15m(Barrier-free space)
Dimming gray scale	4096(2^12)levels
Dimming range	0 -100%
Dimming curve	Logarithmic
PWM Frequency	500Hz(default)

Safety and EMC
EMC standard (EMC)	ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4
Safety standard(LVD	EN 62368-1:2020+A11:2020
Radio Equipment(RED)	ETSI EN 300 328 V2.2.2
Vottun	CE,EMC,LVD,RED

Environment
Operation temperature	Ta: -30°C ~ +55°C
Case temperature (Max.)	T c:+85°C
IP rating	IP20

Warranty and Protection

Ábyrgð

5 ár

Protection

Reverse polarity

Over-heat

Over-load

Skammhlaup

Weight
Net weight	0.234kg
Gross weight	0.054kg

Mechanical Structures and Installations

Wiring Diagram

Note: The RF remote, 0/1-10V dimmer or Push switch can be connected at the same time,

which makes the product more user-friendly and more options to fit for some extra-ordinary demands.

Match Remote Control (two match ways)

End user can choose the suitable match/delete ways. Two options are offered for selection:

Use the controller’s Match key

Match:

Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote. The LED indicator fast flash a few times means match is successful.

Delete:
Press and hold match key for 5s to delete all match, The LED indicator fast flash a few times means all matched remotes were deleted.

Use Power Restart

Match:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 3 times quickly. The light blinks 3 times means match is successful.

Delete:
Switch off the power, then switch on power, repeat again. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times quickly. The light blinks 5 times means all matched remotes were deleted.

0/1-10V Dimming

The 0/1-10V input is operable via commercially available simple rotary wall switchs designed for 0/1-10V dimming equipment or from decicated system central dimming controllers.

Compliant with 0-10V, 1-10V, 10V PWM, RX(4 in 1).
We recommend the number of LED drivers connected to 0/1-10V dimmer does not exceed 5 pieces,The maximum length of the wires from dimmer to LED driver should be no more than 15 metra.

If the controller be used with the RF remote or Push-Dim interface prior to using the 0/1-10V interface,the 0/1-10 V signal should change over 10% to return 0/1-10 V control.

Push Dim Function

The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switchs.

Short press:

Turn on or off light.

Long press (1-6s):

Press and hold to step-less dimming,

With every other long press, the light level goes to the opposite direction.

Dimming memory:

Light returns to the previous dimming level when switched off and on again, even at power failure.

Synchronization:

If more than one controller are connected to the same push switch, do a long press for more than 10s,

then the system is synchronized and all lights in the group dim up to 100%.

This means there is no need for any additional synchrony wire in larger installations.

We recommend the number of controllers connected to a push switch does not exceed 25 pieces,

The maximum length of the wires from push to controller should be no more than 20 metra.

Dimming Curve

Light on/off fade time

Long press match key 5s, then short press match key 3 times, the light on/off time will be set to 3s, the indicator light blink 3 times. Light on/off fade time Long press match key 10s, restore factory default parameter, the light on/off time also restore to 0.5s.

Malfunctions Analysis & Troubleshooting

Malfunctions	Causes	Troubleshooting
No light	1. No power. 2.Wrong connection or insecure.	1.Check the power. 2.Check the connection.
Uneven intensity between front and rear,with voltage drop	1. Output cable is too long. 2. Wire diameter is too small. 3.Overload beyond power supply capability. 4.Overload beyond controller capability.	1.Reduce cable or loop supply. 2.Change wider wire. 3.Replace higher power supply. 4.Add power repeater.
No response from the remote	1.The battery has no power. 2. Beyond controllable distance. 3.The controller did not match the remote.	1. Replace battery. 2.Reduce remote distance. 3. Re-match the remote.

Controller Supply-HM-V1-T-

Q1.ls það í lagi fyrir OEM og ODM ?

Brynjalýsing er fagleg fyrir OEM og ODM pöntun. Við höfum mikla reynslu til að halda áfram framleiðslu og tryggja góð gæði.

Q2.Hvað er MOQ? Má ég fá nokkur sýnishorn ?

Lágt MOQ, 1 stk til að kanna sýnishorn gæði eru fáanleg. Sýnishorn eru ásættanleg og fagna sérsniðnu sýnishornunum fyrir verkefnið þitt.

Q3.Hversu lengi af leiðslutíma?

Dæmi um þarfir 3-5 daga, magnpöntun þarf 10-15 daga

Q4.Hvernig sendir þú vörurnar og hversu langan tíma tekur það að koma?

Við sendum venjulega með DHL, UPS, FedEx eða TNT. Það tekur venjulega 3-5 dagar til að koma. Flugfélag og sjóflutningar einnig valfrjálst.

Q5.Hvernig á að halda áfram pöntun fyrir sérsniðið ljós ?

Fyrst, láttu okkur vita kröfur þínar eða drawing.Second, við vitnum í samræmi við kröfur þínar. Þriðja, þú staðfestir og útvegar greiðslu fyrir formlega pöntun. Að lokum, við munum hefja framleiðslu og skipuleggja sendingu.

Q6.Hversu lengi fyrir ábyrgðina?

Allar Armor lýsingarvörur gæði eru 3 ár, Ef sérsniðnar verkefnavörur með 5 ára ábyrgð.

Q7.Er í lagi að prenta lógóið mitt á vöruna ?

Já, vinsamlegast láttu okkur vita formlega fyrir framleiðslu og staðfestu hönnunina fyrst út frá sýnishorninu okkar.

Q8.Hvernig á að takast á við gallaða?

Við bjóðum 2, 3 og 5 árs takmörkuð ábyrgð fyrir mismunandi tegundir af vörum eða mismunandi kröfur um lýsingarverkefni. Á þessu tímabili, ef viðskiptavinir hafa sönnunargögn sem sýna gæðavandamál og sú sönnun er samþykkt af brynjuljósaverkfræðingum, við viljum skipta þeim gölluðu út fyrir nýja hæfa hluti.

Vinsamlegast athugaðu að ábyrgð er ekki jöfn líftíma. Vörur okkar hafa meira en 50000 klukkustunda langan líftíma.

Q9.Get ég heimsótt verksmiðjuna þína?

Jú,velkomið að heimsækja verksmiðjuna okkar. Getur lætur okkur vita heimsóknaráætlun þína fyrir tvo daga og áhugasamar vörur þínar.

Q10.Ertu verksmiðja eða viðskiptafyrirtæki?

Við erum verksmiðju beint útflutningur til yfir sjó markaði.

Q11. Veitir þú leiddi lýsingu til hvaða fræga vörumerkis sem er?

Já,LED verslunin okkar Lighting var með framboð til LANCOME , Armor Lighting Co.Ltd,Armor Lighting Co.Ltd,Armor Lighting Co.Ltd, Burt's Bee,Armor Lighting Co.Ltd, Armor Lighting Co.Ltd，Armor Lighting Co.Ltd,Armor Lighting Co.Ltd&Armor Lighting Co.Ltd.